|
|
|
|
|
|
|
|
Lip Nurit Operators Guide |
|
The following describes how to perform a
transaction using a Lip Nurit terminal. Use the PROMPTS / YOUR INPUT
prompts
as a guide as to what you should enter. Depending on what
version of the program you have some prompts may not be used
or
may not be in this order. Your terminal can do 4 functions SALE,
VOID, BATCH,
and BRIDGE UPLOAD
SALE
|
PROMPTS |
YOUR INPUT |
|
CREDIT SALE ACCOUNT... |
Press PYMT MODE on 2060,2080,2085 models |
|
CHECK CONVERSION AMOUNT |
Enter the Dollar amount of the check. Terminal may say CHECK SALE AMOUNT instead of CHECK CONVERSION AMOUNT |
|
SWIPE CHECK |
Terminal may say ENTER ACCOUNT. In either case run check through reader. Check goes in left hand slot with the face of the check facing right. Check reader light should blink on & off. If it turns red try again. |
|
SWIPE OR ENTER ID |
Swipe the drivers license through the terminal. If the License does not have a magnetic stripe key in the number. If there are letters press the number key that has the letter and then press the ALPHA COPY key to convert the number to the letter. |
|
ENTER STATE CODE |
Terminal may say DL STATE=**. If the state shown is correct just press enter. In either case enter the state code. Use the guide below for proper state code number. You may also enter the 2 letter abbreviation as well. |
|
|
See the table labeled 'Terminal Responses' below. |
STATE CODES
|
Alabama 10 |
Alaska 12 |
Arizona 14 |
Arkansas 16 |
California 18 |
Colorado 20 |
|
Connecticut 22 |
Delaware 24 |
Florida 26 |
Georgia 28 |
Hawaii 30 |
Idaho 32 |
|
Illinois 34 |
Indiana 36 |
Iowa 38 |
Kansas 40 |
Kentucky 42 |
Louisiana 11 |
|
Maine 13 |
Maryland 15 |
Massachusetts 17 |
Michigan 19 |
Minnesota 21 |
Mississippi 23 |
|
Missouri 25 |
Montana 27 |
Nebraska 29 |
Nevada 31 |
New Hampshire 33 |
New Jersey 35 |
|
New Mexico 37 |
New York 39 |
No. Carolina 41 |
No. Dakota 43 |
Ohio 44 |
Oklahoma 45 |
|
Oregon 46 |
Pennsylvania 47 |
Rhode Island 48 |
So. Carolina 49 |
So. Dakota 50 |
Tennessee 51 |
|
Texas 52 |
Utah 53 |
Vermont 54 |
Virginia 55 |
Wash. DC 56 |
Washington 57 |
|
W. Virginia 58 |
Wisconsin 59 |
Wyoming 60 |
Puerto Rico 61 |
Canada 62 |
SSN 77 |
TERMINAL RESPONSES
|
RESPONSE |
MEANING |
|
AUTH NUM xxxxG |
The transaction is truncated and guaranteed.(Get signature,name, and phone on receipt) |
|
AUTH NUM xxxxV |
The transaction is truncated but not guaranteed.(Get signature, name, & phone on receipt) |
|
NO ACH AUTH NUMxxxxV |
The transaction was not truncated REASONS |
|
DECLINED |
Transaction rejected. Do not accept check. REASONS |
|
ALL OTHERS |
If you received a response not listed here it may be an error. See the page labeled 'Error Definitions' for your terminal configuration. |
A void may only be
done the same day the transaction occurred.
VOID A SALE
|
PROMPTS |
YOUR INPUT |
|
CREDIT SALE ACCOUNT... |
Press PYMT MODE until Terminal responds with CHECK SALE AMOUNT or CHECK CONVERSION AMOUNT |
|
CHECK CONVERSION AMOUNT |
Press the VOID key. Terminal should say CHECK VOID AMOUNT. Enter the amount of the check. |
|
SWIPE CHECK |
Terminal may say ENTER ACCOUNT. In either case run check through reader. Check goes in left hand slot with the face of the check facing right. Check reader light should blink on & off. If it turns red try again. Terminal should respond with 'VOID ACCEPTED'. |
This is not
required since we batch your transactions at midnight each day. It is
provided for informational purposes.
BATCH
|
PROMPTS |
YOUR INPUT |
|
CREDIT SALE ACCOUNT... |
(2080/2085) Press the BATCH key (All others) Press Function & 6 |
|
BATCH ALL ? |
Press ENTER. Terminal should batch out and print a report. The report will show each check attempt. Even if the check was not truncated its amount will appear on this report. Do not use this total as a basis for your account balance. Use the transaction receipts instead or this |
This
is only required if you have a Nurit 3020 terminal & Magtek
Imager.
This procedure transfers the check images to our server.
BRIDGE UPLOAD
|
PROMPTS |
YOUR INPUT |
|
CREDIT SALE ACCOUNT... |
(All but 2085)Press the FUNCTION key and number 6 (2085 only) Press BATCH |
|
1.BATCH TO HOST |
Press 2 and ENTER. Terminal should dial out and transfer the check images. |
© 2000 Global Check Svc. All registered trademarks/trade names belong to their respective owners